What is the point of a MSD box?
MSD’s ignition boxes feature Multiple Sparks at lower RPMS, along with a stronger, hotter, higher voltage spark to completely ignite the mixture.31 Jan 2010
What is the difference between MSD 6A and 6al?
The on-board soft touch rev control is one of the main differences between the 6A and 6AL. This means no external rpm modules to plug in anymore, simply adjust the rotary dials located on top and you are ready to go. Like the 6A box, the 6AL has a primary voltage of 520 540 volts and secondary of 45,000.
Do you need a special timing light for MSD ignition?
MSD ignition should be used with MSD timing lights. Also, consider if your engine is a four-stroke or two-stroke engine. Ensure that the timing light is compatible with your type of engine. You can also buy a light that is universally compatible to avoid some of these problems.29 Dec 2021
How does MSD timing control work?
MSD Timing Controls are designed so engines with locked out timing or crank triggers can take advantage of an ignition curve. The weights and springs inside your existing distributor are removed and the mechanical advance is locked out so the timing is controlled entirely by the MSD Timing Control.
What does the MSD 6AL do?
The MSD 6A is the base model of the capacitive multiple spark discharge 6 Series design. This ignition works on modified street machines, trucks or street rods. The powerful multiple sparks of the MSD 6A ensures complete combustion.
How do you test a 6a L box?
How do I know if my MSD 6al box is bad?
MSD 6AL has a tester that you can test with. Hook it up and put a modified spark plug on a spark plug wire. You can dial in the rpm, observe the spark or check a chip for accuracy.
Can you run a MSD distributor without a MSD box?
MSD 8360 is a “ready to run” distributor and doesn’t need a box.
Does MSD need ignition?
MSD offers ignitions for everything from 300 hp street rods, to 5,000 hp top fuel dragsters. For example, MSD’s 6AL-2. It’s a digitally-controlled ignition that can produce up to 535 volts, has the multi-spark functions, and a built-in rev limiter and 2-step.31 Jan 2010
How do you use a MSD tester?
How do I get rid of rev limiter?
How to remove the RPM limiter? This electronic command module which limits the RPM quantity in order to save your engine from being damaged cannot be physically removed. However, you have the possibility to change the ECU stock with a high performance ECU. This process will authorize you to go beyond the RPM limits.
Does MSD control timing?
The MSD Adjustable Timing Control puts you in control of your ignition timing – from the drivers’s seat! A dash mounted control knob allows you to adjust the ignition timing to compensate for changes in altitude, low octane gas, or heavy loads.
How do you test a MSD magnetic pickup?
Turn the ignition to the On position. DO NOT CRANK THE ENGINE. With a small jumper wire, short the Green and Violet magnetic pickup wires together then pull the jumper off. Each time the short is removed a spark should jump If spark is present, the ignition is working properly.
Does a MSD 6AL control timing?
The high speed controller can make extremely quick compensations to the output voltage, multiple spark series, timing and rpm limits while maintaining precise timing and accurate rev limiting.
How do I turn off MSD rev limiter?
Does a MSD ready to run distributor?
How does MSD BTM work?
The 6 BTM lets you dial away detonation by retarding the timing in relation to the boost pressure. A dash-mounted control knob lets you adjust the amount of timing retard. It can be adjusted from 0 degrees per pound of boost to 3 degrees per pound (up to 15 degrees).
How do you test a magnetic pickup distributor?
Do you need a special timing light for MSD Ignition?
MSD ignition should be used with MSD timing lights. Also, consider if your engine is a four-stroke or two-stroke engine. Ensure that the timing light is compatible with your type of engine. You can also buy a light that is universally compatible to avoid some of these problems.